What LED bulbs fit a 407 SW Coupe (2004-2010)?

A 407 SW Coupe (2004-2010) uses T10 wedge bulbs (W5W/194/168) for the map, door, footwell and license plate lights, and festoon bulbs for the dome and trunk. AutoKitShop stocks 26 407 SW Coupe (2004-2010) kits covering 2004–2014, each supplied with the correct adapters so no separate bulbs are needed.

Does a 407 SW Coupe (2004-2010) need CANbus error-free LEDs?

Most 407 SW Coupe (2004-2010) vehicles built after 2005 monitor the interior lighting circuit and will show a bulb-failure warning with a plain LED. A CANbus error-free kit includes the resistor or decoder that mimics the original load, so the warning stays off. Older vehicles with a simple on/off circuit run fine on standard LEDs.

How long does it take to install 407 SW Coupe (2004-2010) interior LED lights?

Allow 15 to 30 minutes. Switch the light off, pry the lens off with a plastic trim tool, pull the old bulb, push in the LED and test it before refitting the lens. If a bulb does not light, rotate it 180 degrees — LEDs are polarity sensitive. No wiring, coding or tools beyond a trim tool are required.

Will 407 SW Coupe (2004-2010) interior LEDs cause flickering?

Not with an error-free kit. Flickering on a 407 SW Coupe (2004-2010) is normally caused by the body control module pulsing the circuit to test for a failed bulb. The built-in load resistor in an error-free kit absorbs that pulse. If you already own a non-CANbus kit, adding a decoder resolves it.

What colour temperature is best for a 407 SW Coupe (2004-2010)?

White (6000K) matches the factory LED signature on late-model 407 SW Coupe (2004-2010) cars and looks the most OEM. Warm white (3000K) suits older cabins with filament-era trim. Ice blue and purple are aesthetic choices. Colour is selected per bulb, so you can keep the dome white and tint the footwells.

Peugeot 407 SW Coupe (2004-2010) LED Interior Light Kit – 10-Piece Complete Dome, Map & Trunk Upgrade

June 21, 2026

Peugeot 407 SW Coupe LED interior light kit

I've spent time with the Peugeot 407 SW Coupe and it's a car that gets the fundamentals right. What it doesn't get right is the interior lighting. The factory-installed bulbs are barely adequate when new, and they only get dimmer as the filaments age. An LED swap is the cheapest way to bring the cabin lighting up to modern standards.

AutoKitShop's 10-piece CANbus LED kit covers every interior socket in the Peugeot 407 SW Coupe (2004-2010). The swap takes about 15-20 minutes and requires no special tools. No wiring, no coding, no permanent changes.

What Is a 407 SW Coupe (2004-2010) Interior LED Light Kit?

A 407 SW Coupe (2004-2010) interior LED light kit is a set of direct-replacement bulbs that swap into the factory dome, map, reading, vanity, trunk, glove-box and footwell sockets without cutting or rewiring. AutoKitShop lists 26 407 SW Coupe (2004-2010) LED kits covering model years 2004 to 2014. Kits for this model run from 2-piece to 19-piece sets. Each bulb is rated at 300 lumens and roughly 3x the brightness of the original incandescent lamp, at a fraction of the current draw, with a 50,000-hour service life. Kits are supplied as complete sets with the correct socket adapters, so nothing needs to be ordered separately. If a bulb does not light on first fit, rotate it 180 degrees, because LEDs are polarity sensitive. Colour options are white (6000K), ice blue, warm white (3000K) and purple.

What Is Included in the 407 SW Coupe (2004-2010) LED Kit?

This kit is designed for the Peugeot 407 SW Coupe (2004-2010). Every interior bulb position is covered:

Front dome/map lights (x2): Overhead console.
Rear dome lights (x2): Rear seats and cargo area.
Front door courtesy lights (x2): Red-lens, front doors.
Footwell lights (x2): Under-dash lighting.
Glove box light (x1): Compartment light.
Trunk light (x1): Cargo area.

All bulbs use standard sockets — T10 (W5W/194) wedges and festoon 36mm types. Everything is plug-and-play.

How Do LEDs Compare With the Stock Bulbs in a 407 SW Coupe (2004-2010)?

Metric	Stock Bulb	AutoKitShop LED
Light output	~40-50 lumens	~180-220 lumens
Power draw (10 bulbs)	~50W total	~15.0W total
Color temperature	2700-3000K (warm yellow)	6000K (pure white)
Surface temperature	50-80°C	~30°C (barely warm)
Lifespan	~500-1,000 hours	30,000+ hours

Peugeot 407 SW Coupe LED vs stock comparison

How Do You Install LED Interior Lights in a 407 SW Coupe (2004-2010)?

Start with the overhead console — pry the lens off with a trim tool. Door courtesy lenses typically twist out. Trunk lenses pry off from one side. If an LED doesn't light on the first try, rotate it 180 degrees in the socket — LEDs are polarity-sensitive and this resolves 99% of "installation problems."

Important: Turn off lights before starting. Allow stock bulbs to cool if the car was running. If an LED doesn't light, rotate 180 degrees — this is the most common "issue" and it's not an issue, just polarity.

Will LED Bulbs Trigger a Warning Light on a 407 SW Coupe (2004-2010)?

The Peugeot 407 SW Coupe uses CANbus monitoring on select interior circuits. AutoKitShop's bulbs include built-in resistors to prevent warnings and flickering. Everything remains plug-and-play.

Which Colour Temperature Should You Choose?

White ($21.49): Best visibility and contrast. Looks factory-OEM. The recommended choice for most drivers.
Ice Blue ($21.99): Cool tint that matches modern dashboard lighting.
Warm White ($22.99): Closer to stock warmth but 4x brighter.
Purple ($22.99): Custom look that stands out at night.

What Should You Know About Summary?

The Peugeot 407 SW Coupe (2004-2010) benefits enormously from an interior LED upgrade. This 10-piece kit replaces every interior bulb with CANbus-compatible LEDs that are 4x brighter, use 70% less power, and last for the lifetime of the vehicle. Fits all Peugeot 407 SW Coupe variants for the 2004-2010 model years. Plug-and-play installation in under 20 minutes.

Shop the Peugeot 407 SW Coupe 10-Piece CANbus LED Kit